2018 Case CE SV280

Selling Price -

$29,500.00

Information

2018 Case SV280 Skid Steer Loader
74hp 4 Cylinder Turbo Diesel
Hand Controls (ISO or H pattern)
2 Speed Drive
8000lb unit
5600lb tipping load
New Tires & Fresh Service
New 72" Smooth Bucket w/ Bolt on Reversible edge
Local one owner trade
1473 hours
$29,500

Photos

Highlights

  • $29,500.00
  • Newton, North Carolina
  • Pre-Owned
  • 19858
  • 2018
  • Case CE
  • SV280
  • ISM N844LTA-DI-F-45
  • 74
  • 1471
  • Diesel
  • Available
  • Over the tire spec tires: 64.0 in (1.63 m)
  • Bucket hinge pin: 130.0 in (3.30 m) | Top of ROPS: 78.8 in (2.00 m) | Bottom of level bucket, fully raised: 119.6 in (3.04 m) | Dump: with foundry/excavating bucket - 93.7 in (2.38 m) @ 45°, with low profile bucket - 90.7 in (2.31 m) @ 45°

Specifications

  • 2018
  • Case CE
  • SV280
  • Base
  • General
  • ISM N844LTA-DI-F-45
  • Tier 4 Final
  • @ 2800 RPM – SAE J1349: Gross - 74 hp (55 kW), Net - 68 hp (51 kW)
  • Peak @ 1400 RPM: 232 lb·ft (314 N·m)
  • High idle – no load: 2500 +/- 25 rpm | Rated – full load: 2500 Rpm | Low idle: 1150 +/- 25 rpm
  • #: 4
  • 207 in3 (3.4 L)
  • 3.9 in (99 mm)
  • 4.3 in (110 mm)
  • Type: Direct drive countershaft Powershift w/ electronic shift control and inching pedal
  • Travel: Low range - 7.0 mph (11.3 kph)
  • Water | Implement: Gear
  • Water pump: 29 gpm (110 L/min) | Drivetrain: @ rated engine RPM: @ 97% efficiency - 29.4 gpm (111 L/min) | Standard @ rated engine RPM: @ 100% efficiency - 20.6 gpm (78.0 L/min)
  • Charge: 360 psi (24.5 bar) | System relief: 5,220 psi (360 bar)
  • Maximum dump angle: 53.5° | Angle of departure: 23.5° | Clearance circle rear: 70.4 in (1.79 m)
  • Operating: with foundry/excavating bucket - 160.4 in (4.07 m), with low profile bucket - 164.4 in (4.18 m), with low profile extended bucket - 169.5 in (3.04 m)
  • Bucket hinge pin: 130.0 in (3.30 m) | Top of ROPS: 78.8 in (2.00 m) | Bottom of level bucket, fully raised: 119.6 in (3.04 m) | Dump: with foundry/excavating bucket - 93.7 in (2.38 m) @ 45°, with low profile bucket - 90.7 in (2.31 m) @ 45°
  • without attachment with coupler: 117.7 in (2.99 m) | F. with foundry/excavating bucket on ground: 141.9 in (3.60 m) | with low profile bucket: 146.0 in (3.71 m) | with low profile extended bucket: 146.0 in (3.71 m)
  • Over the tire spec tires: 64.0 in (1.63 m)
  • bottom of belly pan: 8.0 in (0.20 m)
  • 52.0 in (1.32 m)
  • Voltage: 24 Volts, negative ground | Starter: 4.29 hp (3.2 kW)
  • 160 amp
  • 12-volt low-maintenance 1,000 cold-cranking amps @ 0° F (-18° C°)
  • Spring-applied, hydraulic release multiple disc.
  • 25.5 gal (96.5 L)
  • Engine w/ filter: 8.9 qt (8.5 L)
  • Hydraulic system: Total - 11.99 gal (45.46 L), Reservoir - 6.0 gal (22.7 L)
  • Unit equipped w/ open cab; 165 lb operator; 72 in Low Profile bucket; full of fuel; 12 x 16.5 tires: 8,090 lb (3 670 kg) | Shipping: 7,665 lb (3 475 kg)